Quality Inspector with VR Training (VR Headset v2 Included)
Do you have a keen attention to detail? A career as a quality inspector could be a great fit. This online quality inspector course will provide you with the knowledge and skills you need to prove competency and begin your new career quickly.
This accelerated quality inspector training provides an intensive overview of the skills necessary for quality assurance and inspection, including math, inspection, safety, materials, quality, and management. As an added bonus, you will help yourself stand out by training with virtual reality technology.
Prepare for a career as a quality inspector, quality technician, quality assurance inspector, quality assurance technician, quality auditor, or quality control inspector
Gain the skills you need to confidently perform your job
You will receive a Meta Quest 2 VR Headset Kit enabling you to complete virtual reality simulations to enhance your learning experience
Here is an Overview of the Benefits of Virtual Reality to get a better understanding of the value this course provides
Attend our exclusive annual virtual National Apprenticeship Week events, featuring live webinars, workshops, and employer interactions
How the course is taught
Self-paced, online course
12 Months to complete
Open enrollment, begin anytime
110 course hours
Outline
Inspection
Basic Measurement 101
Calibration Fundamentals 111
Basics of Tolerance 121
Blueprint Reading 131
Hole Standards and Inspection 141
Thread Standards and Inspection 151
Surface Texture and Inspection 201
Interpreting Prints 231Measuring System Analysis 300
Introduction to GD&T 301
Major Rules of GD&T 311
Inspecting a Prismatic Part 321
Inspecting a Cylindrical Part 331
Advanced Hole Inspection 341
Inspecting with Optical Comparators 351
Inspecting with CMMs 361
Calibration and Documentation 371
In-Line Inspection Applications 381
Lean
Lean Manufacturing Overview 101
Continuous Process Improvement: Managing Flow 124
Continuous Process Improvement: Identifying and Eliminating Waste 125
Developing a Lean Culture 135
5S Overview 151
Cell Design and Pull Systems 161
Intro to Six Sigma 171
Troubleshooting 181
Conducting Kaizen Events 191
SPC Overview 211
Metrics for Lean 231
Process Flow Charting 241
Strategies for Setup Reduction 251
Total Quality Management Overview 261
Management Tools: Problem Solving 270
Management Tools: Product and Process Design 275
Value Stream Mapping: The Future State 311
Maintaining a Consistent Lean Culture 330
Transforming Lean into Business Results 340
Measuring Lean Systems 350
Materials
Introduction to Physical Properties 101
Introduction to Mechanical Properties 111
Introduction to Metals 121
Essentials of Heat Treatment of Steel
Hardness Testing 221
Ferrous Metals 231
Nonferrous Metals 241
Exotic Alloys 301
Metal Cutting
Safety for Metal Cutting 101
Machining Titanium Alloys 325
Quality
ISO 9000 Review 121
Intro to Supply Chain Management 140
Customer-Focused Quality 155
Conducting an Internal Audit 201
TS 16949:2009 Overview 221
Safety
Introduction to OSHA 101
Ergonomics 102
Personal Protective Equipment 111
Noise Reduction and Hearing Conversation 121
Respiratory Safety 131
Lockout/Tagout Procedures 141
SDS and Hazard Communication 151
Bloodborne Pathogens 161
Walking and Working Surfaces 171
Fire and Safety and Prevention 181
Flammable/Combustible Liquids 191
Hand and Power Tool Safety 201
Safety for Lifting Devices 211
Powered Industrial Truck Safety 221
Confined Spaces 231
Environmental Safety Hazards 241
Machine Guarding 271
Shop Essentials (Applied Mathematics)
Math Fundamentals 101
Math: Fractions and Decimals 111
Units of Measurement 112
Algebra Fundamentals 141
Geometry: Lines and Angles 151
Geometry: Triangles 161
Geometry: Circles and Polygons 171
Trigonometry: The Pythagorean Theorem 201
Trigonometry: Sine, Cosine, Tangent 211
Trigonometry: Sine Bar Applications 221
Statistics 231
Supervisor Essentials
Essentials of Leadership 100
Managing Performance: Best Practices 130
Managing Performance: Corrective Actions 135
Basics of Manufacturing Costs 140
Conflict Resolution Principles 150
Conflict Resolution Principles 150
Conflict Resolution for Different Groups 155
Team Leadership 160
Personal Effectiveness 190
Managing the Diverse Workplace 210
Harassment and Discrimination 215
Performance Management and the Law 230
Welding
Material Tests for Welding 201
Fabrication Process 232
Workforce Essentials
Essentials of Communication 115
Virtual Labs/Simulations (optional)
Safety Awareness in Manufacturing
Inspecting Outer Diameters I
Inspecting Outer Diameters II
Inspecting Groove Width
Inspecting Thread Sizes
Inspecting Inside Diameter
Instructors & Support
ToolingU-SME
This is not an instructor-facilitated course; however, support will be provided through email.
Requirements
Prerequisites:
There are no prerequisites to take this course. However, this course requires basic computer skills, including the ability to open and manage windows, navigate websites, and perform common online tasks such as downloading files, completing forms, and using web-based tools.
Requirements:
Hardware Requirements:
This course can be taken on either a PC or Mac.
Software Requirements:
PC: Windows 8 or later.
Mac: macOS 10.6 or later.
Browser: The latest version of Google Chrome or Mozilla Firefox are preferred. Microsoft Edge and Safari are also compatible.
Software must be installed and fully operational before the course begins.
Other:
Email capabilities and access to a personal email account.
Instructional Material Requirements:
The instructional materials required for this course are included in enrollment and will be available online. The following materials will be shipped to you approximately 10 business days after enrollment:
Meta Quest 2 VR Headset Kit (headset, 2 controllers, case, and elite strap)
Material Fees are non-refundable upon registration.
Please note: Due to the high cost of the VR Headset Kit, it will not ship until 10 days after your start date.
FAQ
Based on U.S. Bureau of Labor Statistics data, the average annual salary for quality inspector is $45,850.
A quality inspector is responsible for monitoring the quality of incoming and outgoing products for manufacturing companies.
No.
After you register, you will receive 12 months to complete the course. The time allotted for completion has been calculated based on the number of course hours.
The course includes the Meta Quest 2 headset with the two controllers, a carrying case, and the Elite Strap.
If there are issues with the simulations, you can contact a student advisor and/or access the VR Help Center in the Learning Management System, which includes documentation, videos, and guides to assist with any issues.
If there are any issues with the hardware, you should contact Meta for assistance.
You do not need to have any prior experience with VR technology to take the course. However, if you do not have any experience with VR, we have a Virtual Reality Navigator, a comprehensive guide with tutorials, games, glossary, and best practices in the virtual world.
You do not have to return the headset and accessories once you complete the course, it is included in the cost of this program.
Using virtual reality in learning has many benefits. Here is a link to a document summarizing the many benefits.
For this course, only the 10 labs/simulations are delivered through virtual reality. However, there is an option to complete the simulations on the web.
You have the option of completing the labs in a web browser (Chrome recommended)
Mobile App: Android and Apple
Network bandwidth: A broadband internet connection is required for larger images, audio, video, interactive components, and Virtual Labs.
Screen resolution: The minimum screen resolution recommended is 1024 x 768 pixel
Ram: 8 GB is the minimum recommendation
Graphic Card: Not required but will increase performance of Virtual Labs
This particular VR experience is only compatible with Meta Quest 2 and Meta Quest 3.
Technical support is provided through the robust Hemp Center available in the Learning Management Systems.
If you experience motion sickness or discomfort while using VR, there is an option to complete the labs in a web browser (Chrome recommended).
To access the VR content, you will need to download a specific app from the Meta Quest store. The information for this will be provided upon enrollment.
There is no interaction with instructors and other students in the VR environment.
We have a Virtual Reality Navigator, a comprehensive guide with tutorials, games, glossary, and best practices in the virtual world that can help you get started.
You have the option of completing the labs using virtual reality or web-based simulations. If the VR equipment breaks or malfunctions, you can complete the labs using the web-based versions.
This course is open enrollment, so you can register and start the course whenever you are ready. Access to your course can take 24-48 business hours.
The time allotted for course completion has been calculated based on the number of course hours. However, if you are unable to complete the course, contact the student advising team to see what options you may have available to work out a suitable completion date. Please note that an extension fee may be charged.
Our courses are designed to accommodate various learning preferences. Depending on the course structure, you may get different forms of support. Self-paced courses are designed to be user-friendly and independent, minimizing the need for external support. In courses with instructors, our direct platform support feature includes opportunities for questions, discussions, and remediation, with email and phone support available for select courses. Our student advising team is available to guide you on program requirements and administrative requests, but they do not provide assistance with course content. Our goal is to provide you with the necessary support for success, whether it's through self-paced exploration, direct communication, or guidance from our advising team.
Upon successfully passing the final exam, you will be awarded a certificate of completion from the school or organization that you registered through.
ed2go courses will help you gain the skills you need to obtain an entry-level position in most cases. However, you should always research the job market in your area before enrolling.
ed2go courses are non-credit, so they do not qualify for federal aid, FAFSA, and Pell Grant. In some states, vocational rehab or workforce development boards may provide funding to take our courses. Additionally, you may qualify for financial assistance if you meet certain requirements. Learn more about financial assistance.
If you have questions that are not answered on our website, representatives are available via LIVE chat. You can also call us at 1-877-221-5151 during regular business hours to have your questions promptly answered. If you are visiting us during non-business hours, please send us a question using the "Contact Us."